Tree Sets

[dreamlifter]

Fat Dragon has paper model trees that you can put figures in.


FDG0056Cw.jpg

http://www.fatdragongames.com/fdgfiles/?page_id=347

Thanks for sharing that pic. Those have a nice look and probably don't shed leaves in the fall. Even I can't complain to have something paper like that for easy storage and lighter weight allowing for a higher quantity. If DF found a way, I'd still do that, but I'm going to look into these.

[unclebilly]

I used these. Yea I know they are not grand looking but they are more parctical for RPGing. You can put minis on them and they fold up for easy storage and transportation. https://www.kickstarter.com/projects/wo ... -table-top

For looks I also have some of these. https://www.dungeoncrawler.com/store/in ... er=product

Like your new "look" U.B. - Yo-Ho-Ho
Question on the second link. It says "Massive", but has no size stated. Could you let us know how tall and what diameter the canopy is? You gotta love sites that say "View larger" and when you click it's 1 micron bigger.
Is it Resin, Plastic, Rubber - what??? Lastly, how is the detail and what are the leaf clusters like? Solid or?
Those fold-able trees would be nice in a gaming sense, but I'm looking for a bit more for 'my' use.
Thanks, Bill (also called U.B.)

YaRrrr !! They are made of the same stuff as a WoTC mini. If you sign up for their email you can get 25% off any purchases. Here is a picture of one beside a reaper mini. They also sell them unpainted if you want to paint your own. I got the ones that where from the first KS on some of them I had to glue the arm(tree limb) back on but it was worth the discount to me. The arm branch sticking out is the one I had to re glue.

[Vegomatic]

Fat Dragon has paper model trees that you can put figures in.

Fat Dragon 3D Tree

FDG0056Cw.jpg (521.6 KiB) Viewed 5431 times

http://www.fatdragongames.com/fdgfiles/?page_id=347

[William]

I used these. Yea I know they are not grand looking but they are more parctical for RPGing. You can put minis on them and they fold up for easy storage and transportation. https://www.kickstarter.com/projects/wo ... -table-top

For looks I also have some of these. https://www.dungeoncrawler.com/store/in ... er=product

Like your new "look" U.B. - Yo-Ho-Ho
Question on the second link. It says "Massive", but has no size stated. Could you let us know how tall and what diameter the canopy is? You gotta love sites that say "View larger" and when you click it's 1 micron bigger.
Is it Resin, Plastic, Rubber - what??? Lastly, how is the detail and what are the leaf clusters like? Solid or?
Those fold-able trees would be nice in a gaming sense, but I'm looking for a bit more for 'my' use.
Thanks, Bill (also called U.B.)

[LordDust]

"I don't think it is realistic to think of an entire playable village in a single terrain-tree."

I don't think it realistic for Dwarven Forge to make one. I remember one Mary Lee made 15 or 20 years ago.I do not know if I can find the photo. I will look.



1999 I think

Thanks for sharing that one Oldent. I would agree with both of you to an extent. A single tree holding a small village probably isn't a good fit for DF. I plan to make one myself, but I am envisioning more a pseudo-nomadic wood elf tribe, so simple structures largely meant for sleeping in aside from maybe one larger community building. The rest of their living space would be outside in the tree. I was also thinking it wouldn't be hard to make two levels accessible, one on top with full access and the lower one accessible to a shallow depth from the sides. The top area would be a bit smaller in diameter than the layer below to facilitate access below. I could see DF making something with interconnected treetops as has also been discussed, but much as I think I would enjoy such a set I'm not sure if there would be enough demand for DF to make it.

How about making the sand bag a separate component- so that it is only used when "assembled". Ship/transport sans the "bag o dirt", then fill with whatever (sand, dirt, pennies, etc.) at destination.

Were they to try to do this, that could allow for making smaller bases without jacking up shipping. As jackattack has noted, you would need some spread on the base, but adding centralized weight can reduce the amount of spread needed to counteract tip over. You couldn't get away with zero, but reducing it a bit would make it easier to pack and ship, as well as to make molds for.

[Oldent]

OLDENT: I purchased them during Halloween season at Michaels. I purchased some with coupons and picked up all the rest at 70% off sales.

Darnit, yes! I recall seeing them. Didn't register.

The Least Weasel
Totus KS delenda sunt

In was thinking underdark floors. I have not done it yet.

[BaneofHumanity]

I asked him on his FB but got no answer.

[unclebilly]

I used these. Yea I know they are not grand looking but they are more parctical for RPGing. You can put minis on them and they fold up for easy storage and transportation. https://www.kickstarter.com/projects/wo ... -table-top

For looks I also have some of these. https://www.dungeoncrawler.com/store/in ... er=product

By the time I found out about this KS it was over and done with. Do you know if there is any way to purchase these still?

You could try contacting him via contact me on Kickstart and see if he has any for sale.

[GODofwar]

OLDENT: I purchased them during Halloween season at Michaels. I purchased some with coupons and picked up all the rest at 70% off sales.

Darnit, yes! I recall seeing them. Didn't register.

The Least Weasel
Totus KS delenda sunt

[BaneofHumanity]

I used these. Yea I know they are not grand looking but they are more parctical for RPGing. You can put minis on them and they fold up for easy storage and transportation. https://www.kickstarter.com/projects/wo ... -table-top

For looks I also have some of these. https://www.dungeoncrawler.com/store/in ... er=product

By the time I found out about this KS it was over and done with. Do you know if there is any way to purchase these still?